CCNP SPCOR 350-501 Practice Questions & Answers • ExamPrepare

55 questions in this view

Page 1 of 10

Question 1

After frequent issues with link failure between buildings on their main campus, a large company is implementing BFD to provide fast failure detection. The network engineer performing the implementation is told that the failures occur most commonly when large amounts of data are transferred. Which action must the engineer take?

Implement a routing protocol that supports BFD and enables fast convergence.
Implement Cisco Express Forwarding to exclude routers that do not support BFD.
Implement inverse ARP to map Layer 2 addresses properly for faster convergence.
Implement MPLS to allow label switching to store routing decisions.

Select an answer above, then submit your vote. Reading or practicing does not cast a vote.

Question 2

Refer to the exhibit. A network engineer is trying to retrieve SNMP MIBs with RESTCONF on the Cisco switch but fails. End-to-end routing is in place. Which configuration must the engineer implement on the switch to complete the task?

snmp-server community cisco RW
snmp-server community public RO
netconf-yang cisco-ia snmp-community-string Public
netconf-yang cisco-ia snmp-community-string Private

Select an answer above, then submit your vote. Reading or practicing does not cast a vote.

Question 3

What is a constraint of Cisco MPLS TE tunnel configurations?

QoS-aware tunneling is not supported.
With ISIS as an IGP, only older-style metrics are used.
Tunnels cannot span multiple OSPF areas.
Tunnels cannot be configured over IP unnumbered links.

Select an answer above, then submit your vote. Reading or practicing does not cast a vote.

Question 4

Refer to the exhibit. A Cisco engineer is implementing gRPC dial-out on an ASR. Receiver 192.168.1.1 will be assigned one of the subscriptions, and it will manage the ASR. Which command is needed to complete the router configuration?

protocol grpc
protocol tcp
protocol all
protocol any

Select an answer above, then submit your vote. Reading or practicing does not cast a vote.

Question 5

A network engineer is implementing a QoS policy for outbound management traffic classification and marking on a CPE device with these requirements:

• Management protocols must be marked with DSCP AF class 2 with low drop probability.

• Monitoring protocols must be marked with DSCP AF class 1 with low drop probability.

• All remaining traffic must be marked with a DSCP value of 0.

Which configuration must the engineer implement to satisfy the requirements?

policy-map cpe-mgmt-policy class management set ip dscp af21 class monitoring set ip dscp af11 class class-default set ip dscp default end
policy-map cpe-mgmt-policy class management set ip dscp af21 class monitoring set ip dscp af11 class class-default set ip dscp af0 end
policy-map cpe-mgmt-policy class management set ip dscp af23 class monitoring set ip dscp af13 class class-default set ip dscp default end
policy-map cpe-mgmt-policy class management set ip dscp af23 class monitoring set ip dscp af13 class class-default set ip dscp af0 end

Select an answer above, then submit your vote. Reading or practicing does not cast a vote.

Question 6

Refer to the exhibit. An administrator working for large ISP must connect its two POP sites to provide internet connectivity to its customers. Which configuration must the administrator perform to establish an iBGP session between routers PE1 on POP site 1 and PE2 on POP site 2?

PE2# configure terminal PE2(config)# router bgp 65111 PE2(config-router)# address-family ipv4 unicast PE2(config-router-af)# neighbor 172.18.10.1 activate PE2(config-router-af)# end
PE1# configure terminal PE1(config)# router bgp 65111 PE1(config-router)# address-family ipv4 unicast PE1(config-router-af)# neighbor 172.19.10.10 activate PE1(config-router-af)# end
PE2# configure terminal PE2(config)# router bgp 65111 PE2(config-router)# no neighbor 172.18.10.1 shutdown PE2(config-router)# end
PE1# configure terminal PE1(config)# router bgp 65111 PE1(config-router)# no neighbor 172.19.10.10 shutdown PE1(config-router)# end

Select an answer above, then submit your vote. Reading or practicing does not cast a vote.